Herz pelletstar CONDENSATION 10 Operating Instructions Manual Download

Page: 32 / 94

T-CONTROL

9.12.1

Boiler

Navigation:

→

BOILER

Screen:

By pressing the button:

the „boiler status“ menu will be displayed
(Schematic representation of the boiler and overview of various values)

the menu for the "settings" will be displayed

the menu "inputs / outputs" (system-specific) will be displayed

the menu "operating hours" will be displayed

Term

Description

Unit

„Boiler Status“

Status 1

2 3 4

Boiler temperature

Indicates the boiler temperature

°C

Back flow temperature

Indicates the back flow temperature

°C

Boiler power

Indicates the boiler output

Back flow mixer

Indicates the actual state of the back flow mixer (OPEN/CLOSE)

Back flow pump

Indicates the actual state of the back flow pump (ON/OFF)

Status 2

3 4

Status time

The status time indicates how long the boiler has been in the current
boiler status.

min

Flue gas temperature

Indicates the flue gas temperature

°C

combustion chamber
temperature

Display of the combustion chamber temperature (= inlet heat
exchanger)

°C

Stoker temperature

Indicates the stoker screw temperature (= feeding screw temperature)

°C

Status 3

1 2

ID fan

Display of the actual control of the ID-fan

Summary of Contents for pelletstar CONDENSATION 10































































































Search results

Summary of Contents for pelletstar CONDENSATION 10

Reviews:

Related manuals for pelletstar CONDENSATION 10

Brands by name

Popular brands

Herz pelletstar CONDENSATION 10, Operating Instructions Manual

Search results

Summary of Contents for pelletstar CONDENSATION 10

Reviews:

Related manuals for pelletstar CONDENSATION 10

Brands by name

Popular brands