Herz pelletstar CONDENSATION 10 Operating Instructions Manual Download

Page: 28 / 94

T-CONTROL

Navigation 3:

Load scheme

Navigation 4:

Show value BOILER 000

Screen:

Note:

By pressing the button:

The values of the default scheme can also be
adapted individually. There by press 3-5 seconds on
the value and follow the procedure described in
figure "boiler display value select".

Boiler-must,

Power, Back

flow-must, etc.

the value will be confirmed and
displayed at the main menu.

the page previous page of the
individual

modules

will

displayed

you get to the second page of the
display values of the boiler or the
selected module

Note:

The same procedure can be applied to all other
modules.

9.8.2

Delete values

Delete all display values

Delete optional display value

Navigation:

Code

– entry

→

Symbol

→

press on an empty field

→

Clear

all

Navigation:

Code

– entry

→

press 3-5

seconds on the to deleted value

→

Act. clear

Screen:

Summary of Contents for pelletstar CONDENSATION 10































































































Search results

Summary of Contents for pelletstar CONDENSATION 10

Reviews:

Related manuals for pelletstar CONDENSATION 10

Brands by name

Popular brands

Herz pelletstar CONDENSATION 10, Operating Instructions Manual

Search results

Summary of Contents for pelletstar CONDENSATION 10

Reviews:

Related manuals for pelletstar CONDENSATION 10

Brands by name

Popular brands