![background image](http://html.mh-extra.com/html/heidenhain/tnc-620-programming-station/tnc-620-programming-station_user-manual_2118726023.webp)
TNC model, software and features
HEIDENHAIN | TNC 620 | ISO Programming User's Manual | 9/2016
23
In operating modes
Program run, single block
and
Program
run, full sequence
the screen layout
P SECTS
can be
specified, see "Structuring programs", page 172
In operating modes
Program run full sequence
,
Program run
single block
and
Positioning with manl.data input
, the font
size can be set to the same size as the
Programming
operating
mode, see "Machine-specific user parameters", page 624
The functions in the
Positioning with manl.data input
mode
were expanded and adapted for improved operation, see
"Positioning with Manual Data Input", page 549
Active kinematics is displayed in the operating mode
RETRACT
,
see "Retraction after a power interruption", page 578
In
RETRACT
operating mode, feed-rate limitation can be
deactivated with the soft key
CANCEL THE FEED RATE
LIMITATION
, see "Retraction after a power interruption",
In
Test run
operating mode a tool usage file can also be created
without simulation, see "Tool usage test", page 218
In
Test run
operating mode the soft key
FMAX PATHS
hides
the rapid traverse movements, see "3-D view in the Test Run
operating mode", page 560
In
Test run
operating mode the soft key
RESET THE VOLUME
MODEL
resets the solid model, see "3-D view in the Test Run
In
Test run
operating mode the soft key
RESET TOOL PATHS
resets the tool paths, see "3-D view in the Test Run operating
mode", page 560
In
Test run
operating mode the soft key
MEASURING
displays
the coordinates if you position the mouse on the graphics, see
"3-D view in the Test Run operating mode", page 560
In
Test run
operating mode the soft key
STOP AT
simulates
up to a predefined block, see "Test run up to a certain block ",
page 571
Active basic transformation is shown in the status display on the
POS
tab, see "Positions and coordinates (POS tab)", page 89
The status display now also shows the path of the active main
program, see "Overview", page 87, see "General program
information (PGM tab)", page 87
In the status display the
CYC
tab now also shows
T-Max
and
TA-Max
Mid-program startup can now be continued, see "Any entry into
program: Mid-program startup", page 581
With functions
NC/PLC Backup
and
NC/PLC Restore
you can
save and restore single directories or the complete TNC drive,
see "Backup and restore", page 101
Summary of Contents for TNC 620 Programming Station
