Hardi ISOBUS VT, Operator'S Manual

Page: 33 / 104

3 - Description
3.21
3. 5 Tank gauge calibration Setup density of chemical or fertilizer. Calibration for tank size and shape
3. 5. 1 Adjustment of specific gravity Enter weight of liquid fertilizer divided by weight of water (e.g. 1.10 to 1.30)
3. 5. 2 Calibration of Tank gauge Calibrate if factory calibration is not adequate. Disable SafeTrack
3. 5. 2. 1 Water level Fill up the tank to the max level, then press Enter
3. 5. 2. 2 Water level Level the sprayer, then press Enter
3. 5. 2. 3 Water level Empty sprayer through main flow meter at boom. Computer will register flow
3. 5. 2. 4 Water level Key in true volume from flowmeter. Computer will calculate table
3. 5. 3 Select factory calibration Select preloaded factory calibration for Hardi® tanks or custom calibration
3. 5. 3. 1 Custom calibration of gauge Tank gauge table from custom Calibration
3. 5. 3. 2 CME 3300 factory calibration Factory tank gauge table for CME 3300
3. 5. 3. 3 CME 4500 factory calibration Factory tank gauge table for CME 4500
3. 5. 3. 4 CME 7000 factory calibration Factory tank gauge table for CME 7000
3. 5. 3. 5 CME 9000 factory calibration Factory tank gauge table for CME 9000 AUS
3. 5. 3. 6 Alpha 2500 factory calibration Factory tank gauge table for Alpha 2500
3. 5. 3. 7 Alpha 3500 factory calibration Factory tank gauge table for Alpha 3500
3. 5. 3. 8 Alpha 4100 factory calibration Factory tank gauge table for Alpha 4100
3. 5. 3. 9 Alpha 3000 factory calibration Factory tank gauge table for Alpha 3000
3. 5. 3. 10 CME 5x00 factory calibration Factory tank gauge table for CME 5x00 AUS
3. 5. 3. 11 CME 7x00 factory calibration Factory tank gauge table for CME 7x00 AUS
3. 5. 3. 12 Saritor 4000 factory cal Factory tank gauge table for Saritor 4000
3. 5. 3. 13 Saritor 5000 factory cal Factory tank gauge table for Saritor 5000
3. 5. 3. 14 Navigator 3000 factory cal Factory tank gauge table for Navigator 3000
3. 5. 3. 15 Navigator 4000 factory cal Factory tank gauge table for Navigator 4000
3. 5. 3. 16 CME 5500 factory cal Factory tank gauge table for CME 5500 EU US
3. 5. 3. 17 CME 10,000 factory cal Factory tank gauge table for CME 10,000
3. 5. 3. 18 Navigator 5000 factory cal Factory tank gauge table for Navigator 5000
3. 5. 3. 19 Navigator 6000 factory cal Factory tank gauge table for Navigator 6000
3. 5. 3. 20 Presidio 2700 factory cal Factory tank gauge table for Presidio 2700 EU US
3. 5. 4 Offset at empty MainTank Actual frequency. Accept if empty. Or key in recorded empty-frequency
3. 5. 4. 1 TankGauge Offset,
3. 6 Track calibration Track width, tractor drawbar length, damping, alignment, sensitivity set up
3. 6. 1 Track width Track width of the sprayer wheels measured center to center
3. 6. 2 Tractor drawbar Tractor drawbar length is length from tractor rear axle to pin-bolt
3. 6. 3 Dead zone for regulation Increase for high speed. Decrease for high accuracy
3. 6. 4 Damping of hydraulics Increase for smooth drive and high speed. Decrease for high accuracy
3. 6. 5 Align right - left Alignment of sprayer. Positive value moves sprayer right, negative left
3. 6. 6 Calibrate sensitivity Adjustment of track sensitivity in relation to the tractor hydraulics
3. 6. 6. 01 Sensitivity tractor hydraulic Press ESC to abort. Press Enter to start calibration of offset and gain
3. 6. 6. 02 Finding offset right side Press hold 'steer to right' button. Computer will activate valve to find offset
3. 6. 6. 03 Offset right side is Ok
3. 6. 6. 04 Finding offset right failed Press Enter to return to Track calibration menu
3. 6. 6. 05 Finding offset left side Press hold 'steer to left' button. Computer will activate valve to find offset
3. 6. 6. 06 Offset left side is Ok
3. 6. 6. 07 Finding offset left failed Press Enter to return to Track calibration menu
3. 6. 6. 08 Finding gain right side Press hold 'steer to right' button. Computer will activate valve and find gain
3. 6. 6. 09 Gain right side is Ok
3. 6. 6. 10 Find gain right side failed Press Enter to return to Track calibration menu
3. 6. 6. 11 Finding gain left side Press hold 'steer to left' button. Computer will activate valve and find gain
3. 6. 6. 12 Gain left side is Ok Calibration is OK. Press Enter to return to Track calibration menu
3. 6. 6. 13 Finding gain left side failed Press Enter to return to Track calibration menu
3. 6. 6. 14 Stop driving Stop driving
3. 6. 6. 15 Switch to auto Switch to auto track
4 Toolbox Helpful tools e.g. measure distance and area, service intervals, test etc
4. 1 Measure To measure distance and area. Setup working width
4. 1. 1 Measure Distance This is a simple electronic 'measuring tape'. You can measure distance
4. 1. 1. 1 Measure Distance Measure stopped. Press C to clear, Enter to start and ESC to exit