H3C WX Series Command Reference Manual Download Page 88 | Manualshive

Page: 88 / 200

background image

88

Use the

undo idle-timeout

command to restore the default.

The default idle-timeout is 10 minutes.

NOTE:



The system automatically terminates the user’s connection if there is no information
interaction between the device and the user in timeout time.



Setting idle-timeout to zero disables the timer and the connection is maintained whether it is
idle or not.

Examples

Set the idle-timeout timer to 1 minute and 30 seconds.

<Sysname> system-view
[Sysname] user-interface console 0
[Sysname-ui-console0] idle-timeout 1 30

lock

Syntax

lock

View

User view

Default Level

3: Manage level

Parameters

None

Description

Use the

lock

command to set a password to prevent unauthorized users from operating

under the active user interface.

After entering the

lock

command, you are prompted to input a password (up to 16

characters) and then confirm it by inputting the password again. The password is
successfully set only when you input the exact password during the confirmation. After
setting the password, you are required to input the password next time you enter the
system.

By default, this function is disabled.

Examples

Lock the active user interface.

«
...
86
87
88
89
90
...
»

Summary of Contents for WX Series









































































































































































































Reviews:

No comments

Related manuals for WX Series

Relion 670 series

Brand: ABB Pages: 760

Brand: ABB Pages: 128

Brand: Fantech Pages: 2

Brand: IBM Pages: 276

Brand: IBM Pages: 32

Brand: IBM Pages: 157

SIGMA CONTROL 2

Brand: KAESER KOMPRESSOREN Pages: 246

Brand: Samson Pages: 20

Brand: National Instruments Pages: 6

Brand: National Instruments Pages: 6

Brand: Samson Pages: 8

Brand: Samson Pages: 60

Brand: Samson Pages: 40

Brand: RadioMaster Pages: 10

Brand: Xblue Networks Pages: 2

Brand: Apex Toys Pages: 7

Brand: Zencontrol Pages: 2

Brand: Gasboy Pages: 119

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands