H3C WX Series Command Reference Manual Download Page 192

Page: 192 / 200

192

Field

Description

Active

Number of patches in the ACTIVE state

Start-Address

Starting address of the memory patch area in the memory

patch active

Syntax

patch active

patch-number

View

System view

Default Level

3: Manage level

Parameters

patch-number

: Sequence number of a patch. The valid values of this argument

depend on the patch file used.

Description

Use the

patch active

command to activate the specified patch, namely, the system

will run the patch.

After you execute the command all the DEACTIVE patches before the specified patch
are activated.

The command is not applicable to patches in the DEACTIVE state.

After a system reboot, the original ACTIVE patches change to DEACTIVE, and become
invalid. To make them effective, you must activate them again.

Examples

Activate patch 3 and all the DEACTIVE patches before patch 3.

<Sysname> system-view
[Sysname] patch active 3

patch deactive

Syntax

patch deactive

patch-number

View

System view

Summary of Contents for WX Series









































































































































































































Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands

H3C WX Series, Command Reference Manual

Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands