H3C WX Series Command Reference Manual Download Page 166

Page: 166 / 200

166

Examples

Set the name of the local time zone to

, five hours ahead of UTC time.

<Sysname> system-view
[Sysname] clock timezone z5 add 5

configure-user count

Syntax

configure-user count

number

undo configure-user count

View

System view

Default Level

2: System level

Parameters

number

: Number of users, the value range varies with ACs.

Description

Use the

configure-user count

command to configure the number of users allowed to

enter system view at the same time.

Use the

undo configure-user count

command to restore the default.

Two users are allowed to configure in system view by default.

Related commands:

display configure-user

NOTE:



When multiple users enter system view to configure certain attribute, only the last
configuration applies.



When the number of users has already reached the limit, other users cannot enter system
view.

Examples

Configure the limit of users as 4.

<Sysname> system-view
[Sysname] configure-user count 4

Summary of Contents for WX Series









































































































































































































Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands

H3C WX Series, Command Reference Manual

Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands