H3C WX Series Command Reference Manual Download Page 95

Page: 95 / 200

Parameters

None

Description

Use the

shell

command to enable terminal services on the user interface.

Use the

undo shell

command to disable this function.

By default, terminal services are enabled on all user interfaces.

There are a few restrictions on using the

undo shell

command:



This command is not supported on the console port.



This command is not supported on the AUX port if the device has only a AUX port
and no console port.



This command cannot be used on the user interface from which you log in.

Examples

Disable terminal services on the VTYs 0 through 4.

<Sysname> system-view

[Sysname] user-interface vty 0 4
[Sysname-ui-vty0-4] undo shell
% Disable ui-vty0-4 , are you sure? [Y/N]:y

[Sysname-ui-vty0-4]

The following information is displayed when a Telnet terminal logs in:

The connection was closed by the remote host!

speed (in user interface view)

Syntax

speed

speed-value

undo speed

View

User interface view

Default Level

2: System level

Parameters

speed-value

: Transmission rate in bps.

The transmission rates available with asynchronous serial interfaces include:



300 bps

Summary of Contents for WX Series









































































































































































































Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands

H3C WX Series, Command Reference Manual

Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands