H3C WX Series Command Reference Manual Download Page 36

Page: 36 / 200

FTP configuration commands

FTP server configuration commands

display ftp-server

Syntax

display ftp-server

View

Any view

Default Level

3: Manage level

Parameters

None

Description

Use the

display ftp-server

command to display the FTP server configuration.

After configuring FTP server parameters, you may verify them with this command.

Related commands:

ftp server enable

ftp timeout

, and

ftp update

Examples

Display the FTP server configuration.

<Sysname> display ftp-server
FTP server is running
Max user number: 1

User count:                   1
Timeout value(in minute):     30
Put Method:                   fast

Table 1

display ftp-server

command output description

Field

Description

Max user number

Maximum number of login users at a time

User count

Number of the current login users

Summary of Contents for WX Series









































































































































































































Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands

H3C WX Series, Command Reference Manual

Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands