H3C WX Series Command Reference Manual Download Page 83

Page: 83 / 200

display users

Syntax

display users

[

all

]

View

Any view

Default Level

1: Monitor level

Parameters

all

: Displays information about all user interfaces that the device supports.

Description

Use the

display users

command to display the information about the user interfaces

being used.

Use the

display users all

command to display the information about all the user

interfaces supported on the device.

Examples

Display the information about the user interfaces being used.

<Sysname> display users
The user application information of the user interface(s):
Idx UI Delay Type Userlevel

+ 1 VTY 0 00:00:00 TEL 3
2 VTY 1 00:02:34 TEL 3

Following are more details.
VTY 0 :
User name: admin

        Location: 192.168.1.54
VTY 1   :
        User name: admin

        Location: 192.168.1.58
+   : Current operation user.
F   : Current operation user work in async mode.

The above information shows that at present two users have logged in to the device.
One is from VTY 0 with the IP address of 192.168.1.54 and the other is from VTY 1 with the
IP address of 192.168.1.58.

Summary of Contents for WX Series









































































































































































































Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands

H3C WX Series, Command Reference Manual

Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands