H3C WX Series Command Reference Manual Download Page 96

Page: 96 / 200



600 bps



1200 bps



2400 bps



4800 bps



9600 bps



19200 bps



38400 bps



57600 bps



115200 bps

The transmission rate varies with devices and configuration environment.

Description

Use the

speed

command to set the transmission rate on the user interface.

Use the

undo speed

command to restore the default transmission rate.

By default, the transmission rate is 9600 bps.

NOTE:



The command is only applicable to asynchronous serial interfaces (including AUX and
console ports).



The transmission rate setting on the terminal must be the same as that on the device user
interface for communication.

Examples

Set the transmission rate on the user interface AUX 0 to 19200 bps.

<Sysname> system-view

[Sysname] user-interface aux 0
[Sysname-ui-aux0] speed 19200

stopbits

Syntax

stopbits

{

1.5

}

undo stopbits

View

User interface view

Summary of Contents for WX Series









































































































































































































Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands

H3C WX Series, Command Reference Manual

Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands