H3C WX Series Command Reference Manual Download Page 32

Page: 32 / 200

undo sysname

View

System view

Default Level

2: System level

Parameters

string

: System name of the access controller, a string of 1 to 30 characters. The system

default is

H3C

Description

Use the

sysname

command to set the system name for the access controller.

Use the

undo sysname

command to revert to the default system name.

The CLI prompt reflects the system name of an access controller. For example, if the
system name of an access controller is

H3C

, then the prompt of user view is <H3C>.

Examples

Set the system name of the access controller to

ABC

<Sysname> system-view

System View: return to User View with Ctrl+Z.
[Sysname] sysname ABC
[ABC]

telnet

Syntax

telnet

remote-host

[

service-port

] [

source

{

interface

interface-type

interface-number

ip-address

} ]

View

User view

Default Level

0: Visit level

Parameters

remote-host

: IPv4 address or host name of a remote system, a string of 1 to 20

characters, case insensitive.

service-port

: TCP port number for the remote system to provide Telnet services. It ranges

from 0 to 65535 and defaults to 23

source

: Specifies the source interface or source IPv4 address of Telnet packets.

Summary of Contents for WX Series









































































































































































































Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands

H3C WX Series, Command Reference Manual

Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands