H3C WX Series Command Reference Manual Download Page 118

Page: 118 / 200

118

Configuration file management

commands

archive configuration

Syntax

archive configuration

View

User view

Default Level

3: Manage level

Parameters

None

Description

Use the

archive configuration

command to save the current running configuration

manually.

After the execution of this command, the system saves the current running
configuration with the specified filename (filename serial number) to the
specified path.

Before executing the

archive configuration

command, configure the filename prefix

and path of the saved configuration file by using the

archive configuration location

command.

Examples

Save the current running configuration manually.

<Sysname> archive configuration

Warning: Save the running configuration to an archive file. Continue? [Y/N]: Y
Info: The archive configuration file myarchive_1.cfg is saved.

archive configuration interval

Syntax

archive configuration interval

minutes

Summary of Contents for WX Series









































































































































































































Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands

H3C WX Series, Command Reference Manual

Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands