manualshive.com logo in svg

GigaDevice Semiconductor GD32E23 Series, User Manual

Share
Download
GigaDevice Semiconductor GD32E23 Series User Manual Download Page 534

                                                                                                                     

GD32E23x User Manual

 

534 

 

 

RXFIFO that generate RBNE. 

0: Half-word access, and RBNE is generated when RXLVL >= 2. 

1: Byte access, and RBNE is generated when RXLVL >= 1. 

11:8 

DZ[3:0] 

Date size (only for SPI1) 

This field indicates the data size for transfer.   

0000: Force to “0111” 

0001: Force to “0111” 

0010: 

Force to “0111” 

0011: 4-bit 

0100: 5-bit 

…… 

1111: 16-bit 

7 

TBEIE 

Transmit buffer / TXFIFO empty interrupt enable 

0: Disable TBE interrupt 

1: Enable TBE interrupt. An interrupt is generated when the TBE bit is set. 

6 

RBNEIE 

Receive buffer / RXFIFO not empty interrupt enable 

0: Disable RBNE interrupt. 

1: Enable RBNE interrupt. An interrupt is generated when the RBNE bit is set. 

5 

ERRIE 

Errors interrupt enable. 

0: Disable error interrupt   

1:  Enable  error  interrupt.  An  interrupt  is  generated  when  the  CRCERR  bit  or  the 

CONFERR bit or the FERR bit or the RXORERR bit or the TXURERR bit is set.   

4 

TMOD 

SPI TI mode enable. 

0: Disable SPI TI mode 

1: Enable SPI TI mode   

3 

NSSP 

SPI NSS pulse mode enable. 

0: Disable SPI NSS pulse mode   

1: Enable SPI NSS pulse mode 

2 

NSSDRV 

Drive NSS output 

0: Disable master NSS output 

1: Enable master NSS output 

1 

DMATEN 

Transmit buffer / TXFIFO DMA enable 

0: Disable transmit buffer / TXFIFO DMA. 

1: Enable transmit buffer / TXFIFO DMA, when the TBE bit in SPI_STAT is set, it 

will be a DMA request on corresponding DMA channel. 

0 

DMAREN 

Receive buffer / RXFIFO DMA enable 

0: Disable receive buffer / RXFIFO DMA   

1: Enable receive buffer / RXFIFO DMA, when the RBNE bit in SPI_STAT is set, it 

will be a DMA request on corresponding DMA channel.   

Summary of Contents for GD32E23 Series




































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands