manualshive.com logo in svg

GigaDevice Semiconductor GD32E23 Series, User Manual

Share
Download
GigaDevice Semiconductor GD32E23 Series User Manual Download Page 372

                                                                                                                     

GD32E23x User Manual

 

372 

 

 

31:11 

Reserved 

Must be kept at reset value 

10 

CH1OF 

Channel 1 over capture flag 

Refer to CH0OF description 

9 

CH0OF 

Channel 0 over capture flag 

When  channel 0  is configured  in  input mode,  this  flag  is  set  by  hardware  when  a 

capture event occurs while CH0IF flag has already been set. This flag is cleared by 

software. 

0: No over capture interrupt occurred 

1: Over capture interrupt occurred 

8 

Reserved 

Must be kept at reset value. 

7 

BRKIF 

Break interrupt flag 

When the break input is inactive, the bit is set by hardware.   

When the break input is inactive, the bit can be cleared by software. 

0: No active level break has been detected. 

1: An active level has been detected. 

6 

TRGIF 

Trigger interrupt flag 

This flag is set on trigger event and cleared by software. When in pause mode, both 

edges on trigger input generates a trigger event, otherwise, only an active edge on 

trigger input can generates a trigger event. 

0: No trigger event occurred. 

1: Trigger interrupt occurred. 

5 

CMTIF 

Channel commutation interrupt flag 

This  fl

ag  is  set  by  hardware  when  channel’s  commutation  event  occurs,  and 

cleared by software 

0: No channel commutation interrupt occurred 

1: Channel commutation interrupt occurred 

4:3 

Reserved 

Must be kept at reset value 

2 

CH1IF 

Channel 1 ‘s capture/compare interrupt flag 

Refer to CH0IF description 

1 

CH0IF 

Channel 0 ‘s capture/compare interrupt flag 

This  flag is  set  by  hardware  and cleared by  software. When  channel  0  is in input 

mode,  this  flag  is  set  when  a  capture  event  occurs. When  channel  0  is  in  output 

mode, this flag is set when a compare event occurs. 

0: No Channel 0 interrupt occurred 

1: Channel 0    interrupt occurred 

0 

UPIF 

Update interrupt flag 

This bit is set by hardware on an update event and cleared by software. 

0: No update interrupt occurred 

Summary of Contents for GD32E23 Series




































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands