GigaDevice Semiconductor GD32E23 Series User Manual Download Page 367

Page: 367 / 547

GD32E23x User Manual

367

The counter generates an overflow or underflow event

UPDIS

Update disable.

This bit is used to enable or disable the update event generation.

0: Update event enable. When an update event occurs, the corresponding shadow

registers are loaded with their preloaded values. These events generate update

event:

The UPG bit is set

The counter generates an overflow or underflow event

The restart mode generates an update event.

1: Update event disable.

Note:

When this bit is set to 1, setting UPG bit or the restart mode does not

generate an update event, but the counter and prescaler are initialized.

CEN

Counter enable

0: Counter disable

1: Counter enable

The CEN bit must be set by software when timer works in external clock, pause

mode and encoder mode.

Control register 1 (TIMERx_CTL1)

Address offset: 0x04

Reset value: 0x0000 0000

This register has to be accessed by word(32-bit)

Reserved

ISO1

ISO0N

ISO0

Reserved

MMC[2:0]

DMAS

CCUC

Reserved

CCSE

Bits

Fields

Descriptions

31:11

Reserved

Must be kept at reset value

ISO1

Idle state of channel 1 output

Refer to ISO0 bit

ISO0N

Idle state of channel 0 complementary output

0: When POEN bit is reset, CH0_ON is set low.

1: When POEN bit is reset, CH0_ON is set high

This bit can be modified only when PROT [1:0] bits in TIMERx_CCHP register is

00.

ISO0

Idle state of channel 0 output

Summary of Contents for GD32E23 Series




































































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32E23 Series

Reviews:

Brands by name

Popular brands

GigaDevice Semiconductor GD32E23 Series, User Manual

Search results

Summary of Contents for GD32E23 Series

Reviews:

Brands by name

Popular brands