GigaDevice Semiconductor GD32E23 Series User Manual Download Page 465

Page: 465 / 547

GD32E23x User Manual

465

This register must be written only when TBE bit in USART_STAT register is set.

16.4.12.

USART coherence control register (USART_CHC)

Address offset: 0xC0

Reset value: 0x0000 0000

This register has to be accessed by word (32-bit).

Reserved

EPERR

Reserved

HCM

w0c

Bits

Fields

Descriptions

31:9

Reserved

Must be kept at reset value.

EPERR

Early parity error flag. This flag will be set as soon as the parity bit has been

detected, which is before RBNE flag. This flag is cleared by writing 0.

0: No parity error is detected

1: Parity error is detected.

7:1

Reserved

Must be kept at reset value.

HCM

Hardware flow control coherence mode

0: nRTS signal equals to the RBNE in status register

1: nRTS signal is set when the last data bit (parity bit when pce is set) has been

sampled.

16.4.13.

USART receive FIFOcontrol and status register (USART_RFCS)

Address offset: 0xD0

Reset value: 0x0000 0400

This register has to be accessed by word (32-bit).

Reserved

RFFINT

RFCNT[2:0]

RFF

RFE

RFFIE

RFEN

Reserved

ELNACK

r_w0

Bits

Fields

Descriptions

31:16

Reserved

Must be kept at reset value.

Summary of Contents for GD32E23 Series




































































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32E23 Series

Reviews:

Brands by name

Popular brands

GigaDevice Semiconductor GD32E23 Series, User Manual

Search results

Summary of Contents for GD32E23 Series

Reviews:

Brands by name

Popular brands