GEZE TSA 325 NT Page 48 Installation Instructions Manual Download

Page: 48 / 112

Revolving door TSA 325 NT

Options

Tooth belt crossing with outside-running night-time closer

Tandem rollers (3) must be used for an outside-running night-time closer.

The recesses in the canopy panel must be placed accordingly.

Belt 1

Belt 2

Tandem roller

Tooth belt guidance with rod locking and inside-running night-time closer

An adjustable tandem roller is used in the area of the rod locking to guide the belt for inside-running night-time

closers and guide the tooth belt around the rod locking. The position of the tandem rollers can be adjusted using

an adjustment screw.

Setting the tooth belt tension and rod locking:

Set the tandem roller (1) using an adjustment screw (2).

Summary of Contents for TSA 325 NT

















































































































Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands

GEZE TSA 325 NT, Installation Instructions Manual

Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands