GEZE TSA 325 NT Page 53 Installation Instructions Manual Download

Page: 53 / 112

Revolving door TSA 325 NT

Options

5.6.5 Fill the floor ring space with screed.

Take the screed height in the floor ring into account.

The dimension of 22 mm in the drawing below refers to the standard floor entrance mats of GEZE.

GEZE recommends sealing the surface of the screed in indoor areas.

Pour screed into the drive box and floor ring (1).

* Refers to the standard GEZE entrance mats

5.6.6 Installing the drive

Open the stainless steel panel of the drive.

Install and connect the motor and drive.

Realize the cabling to the sensors.

Use the valid wiring diagram for the wiring and future commissioning.

5.6.7 Inserting side elements

Insert the 4 mm high glazing packers (3).

Place the side elements (1) on the floor ring (4).

Secure the inserted side elements against falling

over by using a strap in the upper third.

Align the side elements exactly.

After mounting has been completed, seal the

open gaps (2).

Summary of Contents for TSA 325 NT

















































































































Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands

GEZE TSA 325 NT, Installation Instructions Manual

Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands