GEZE TSA 325 NT Page 86 Installation Instructions Manual Download

Page: 86 / 112

Revolving door TSA 325 NT

Revolving door TSA 325 NT RC 2

6.3.26 Shortening the tooth belt cut protection

If the toothed belt collides with the cut protection:

Shorten the cut protection (2) so that the toothed belt (1) passes the cut protection without contact.

6.3.27 Adjusting the rod locking

See the supplementary installation instructions for Slimdrive SL WK2 (mat. no. 136308).

6.4 Installation information for NV tooth belt tension RC2

Tooth belt installation with RC 2-rod locking

The tandem roller (if required) is attached to the rear frame profile for RC 2 rod locking. In this case, the toothed

side of the tooth belt must run over the tandem roller.

If the tooth belt rubs against the burglar-protection bracket after installation:

Cut the burglar-protection bracket to length (3).

Belt 1

Belt 2

Burglar-protection bracket

Summary of Contents for TSA 325 NT

















































































































Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands

GEZE TSA 325 NT, Installation Instructions Manual

Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands