GEZE TSA 325 NT Installation Instructions Manual Download

Page: 35 / 112

Revolving door TSA 325 NT

Options

Secure the steel tube against twisting and slipping

at the top and bottom with 2 fitting keys (6) each.

Secure the fitting keys with M3 screws.

Secure M3 screws with thread lock.

Removing fitting keys:

Screw the M3 screws out of the fitting screws.

Screw in M4 screws and press out the fitting

screws with a pull-off tool.

Fitting screws can be removed by using a screw with a larger thread and a pull-off tool.

Fasten the suspension plate of the upper swivelling axis so that the central swivelling axis is position exactly

vertically.

5.2.2 Install BO leaf

The BO leaves are pre-mounted and cabled completely in the factory (including the lower BO axis and the upper

BO flange).

lower BO axis (7)

upper BO axis (8)

Summary of Contents for TSA 325 NT

















































































































Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands

GEZE TSA 325 NT, Installation Instructions Manual

Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands