GEZE TSA 325 NT Installation Instructions Manual Download

Page: 104 / 112

Revolving door TSA 325 NT

104

Revolving door TSA 325 NT, 3-leaf

Mounting the upper pivot bearing on the track side

Mount the upper pivot bearing according to

the drawing:

Screw the counterplate (2) onto the bear-

ing plate (3) with 2 screws (1).

Screw in the 2 threaded pins (4).

The bearing plate (3) must be installed on oppo-

site sides for the right and left leaves.

1 Screws
2 Counterplate
3

Bearing plate

Threaded pins

Stop pins

Swivelling axis for glass leaf

Adjusting the upper pivot bearing

Adjust the upper pivot bearing using

the threaded pins (1) such that the floor

bearing (3) and interior thread (2) for the

threaded rod are flush with one another.

Summary of Contents for TSA 325 NT

















































































































Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands

GEZE TSA 325 NT, Installation Instructions Manual

Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands