GEZE TSA 325 NT Installation Instructions Manual Download

Page: 50 / 112

Revolving door TSA 325 NT

Options

5.6 Revolving door in all-glass version (TSA 325 NT GG)

5.6.1 Box dimensions

Building design

Dimensions

(length x width x depth in mm)

Revolving door TSA 325 NT GG (with drive box)

1404 × 714 × 280

Building shell recess

1500 × 1000 × 300

Optional:

Revolving door TSA 325 NT GG with drive box and exter-

nally mounted control box

900 × 900 × 280

Building shell recess

1000 × 1000 × 300

A depth of at least 60 mm for the cavity is sufficient at manual doors since no drive box is installed.

When digging the cavity provide space for floor guide drainage and cable ducts.

5.6.2 Mounting the floor ring and drive box

Lay 2 floor ring halves (1) and (2) together.

Screw the 2 floor ring halves together using

screws, nuts and washers.

Summary of Contents for TSA 325 NT

















































































































Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands

GEZE TSA 325 NT, Installation Instructions Manual

Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands