GE Ecomagination AF-600 FP, Programming Manual

Page: 48 / 239

The input will go low whenever the Logic
Action [33] Set dig. out. A low is executed.
[82] Logic
Controller
digital output
C
See parameter LC-52 Logic Controller Action .
The input will go high whenever the Logic
Action [40] Set dig. out. A high is executed.
The input will go low whenever the Logic
Action [34] Set dig. out. A low is executed.
[83] Logic
Controller
digital output
D
See parameter LC-52 Logic Controller Action .
The input will go high whenever the Logic
Action [41] Set dig. out. A high is executed.
The input will go low whenever the Logic
Action [35] Set dig. out. A low is executed.
[84] Logic
Controller
digital output
E
See parameter LC-52 Logic Controller Action .
The input will go high whenever the Logic
Action [42] Set dig. out. A high is executed.
The input will go low whenever the Logic
Action [36] Set dig. out. A low is executed.
[85] Logic
Controller
digital output
F
See parameter LC-52 Logic Controller Action .
The input will go high whenever the Logic
Action [43] Set dig. out. A high is executed.
The input will go low whenever the Logic
Action [37] Set dig. out. A low is executed.
[160] No alarm Output is high when no alarm is present.
[161] Running
reverse
Output is high when the frequency
converter is running counter clockwise (the
logical product of the status bits ‘running’
AND ‘reverse’).
[165] Local ref
active
Output is high when
parameter F-02 Operation Method = [2]
Local or when parameter F-02 Operation
Method = [0] Linked to hand auto at the
same time as the keypad is in Hand mode.
[166] Remote ref
active
Output is high when
parameter F-02 Operation Method = Remote
[1] or Linked to hand/auto [0] while the
keypad is in [Auto] mode.
[167] Start
command act.
Output is high when there is an active
Start command (i.e. via digital input bus
connection or [Hand] or [Auto]), and no
Stop or Start command is active.
[168] Hand mode Output is high when the frequency
converter is in Hand mode (as indicated by
the LED light above [Hand]).
[169] Auto mode Output is high when the frequency
converter is in Auto mode (as indicated by
the LED light above [on]).
[180] Clock Fault The clock function has been reset to
default (2000-01-01) because of a power
failure.
[181] Prev.
Maintenance
One or more of the Preventive
Maintenance Events programmed in
parameter T-10 Maintenance Item has
passed the time for the specified action in
parameter T-11 Maintenance Action .
[190] No-Flow A No-Flow situation or Minimum Speed
situation has been detected if enabled in
parameter AP-21 Low Power Detection
and/or parameter AP-22 Low Speed
Detection .
[191] Dry Pump A Dry Pump condition has been detected.
This function must be enabled in
parameter AP-26 Dry Pump Function .
[192] End Of Curve A pump running with max. speed for a
period of time without reaching the set
pressure has been detected. To enable this
function please see parameter AP-50 End of
Curve Function .
[193] Sleep Mode The frequency converter/system has
turned into sleep mode. See parameter
group AP-4#.
[194] Broken Belt A Broken Belt condition has been
detected. This function must be enabled in
parameter AP-60 Broken Belt Function .
[195] Bypass Valve
Control
The bypass valve control (Digital / Relay
output in the frequency converter) is used
for compressor systems to unload the
compressor during start-up by using a
bypass valve. After the start command is
given the bypass valve will be open until
the frequency converter reaches
parameter F-18 Motor Speed Low Limit
[RPM] ) . After the limit has been reached
the bypass valve will be closed, allowing
the compressor to operate normally. This
procedure will not be activated again
before a new start is initiated and the
frequency converter speed is zero during
the receiving of start signal.
Parameter F-24 Holding Time can be used
in order to delay the motor start. The
Bypass valve control principle:
Illustration 3.15
[196] Fire Mode The frequency converter is operating in
Fire Mode. See parameter group FB-0# Fire
Mode .
[197] Fire Mode was
Act.
The frequency converter has been
operating in Fire Mode, but is now back in
normal operation.
[198] Drive Bypass To be used as signal for activating an
external electromechanical bypass
switching the motor direct on line. See
FB-1# Drive Bypass .
[200] Full capacity All pumps running and at full speed
Parameter Description
AF-600 FP
™
Programming Guide
DET-620D 03/2016 All rights reserved. 47
3 3