FE FRENIC-Multi series, Instruction Manual

Page: 82 / 196

5-7
H codes: High Performance Functions
Code
Incre-
ment
Unit
Change
when
running
Data
copying
Default
setting
Refer to
page:
H03 Data Initialization 0: Disable initialization
－ －
N N 0 5-53
1:
2: Initialize motor 1 parameters
3: Initialize motor 2 parameters
H04 Auto-reset (T imes) 1 times Y Y 0
H05 (Reset interval) 0.5 to 20.0 0.1 s Y Y 5.0
H06 Cooling Fan ON/OFF Control 0: Disable (Always in operation)
－ －
Y Y 0 5-56
1: Enable (ON/OFF controllable)
H07 0: Linear
－ －
Y Y 0
1: S-curve (Weak)
2: S-curve (Strong)
3: Curvilinear
H08 0: Disable
－ －
N Y 0 -
1: Enable (Reverse rotation inhibited
）
2: Enable (Forward rotation inhibited
）
H09 Starting Mode (Auto search) 0: Disable
－ －
N Y 0 5-57
1:
2:
H11 Deceleration Mode 0: Normal deceleration
－ －
Y Y 0 5-59
1: Coast-to-stop
H12 0: Disable
－ －
Y Y 1
Limiting 1: Enable
(Mode selection)
H13 0.1 to 10.0 0.1 s Y Y1
Y2
Depending
on the
inverter
capacity
5-23
H14 (Frequency fall rate) 0.00
：
Selected deceleration time 0.01 Hz/s Y Y 999
H16 (Allowable momentary 0.1 s Y Y 999
power failure time)
H26 0: Disable
－ －
Y Y 0 -
1:
H27 (Level) 0.00 to 5.00 0.01 V Y Y 1.60
H28 Droop control -60.0 to 0.0 0.1 Hz Y Y 0.0 5-60
H30 Communications Link Function Run command
－ －
Y Y 0
(Mode selection) 0: F02
1: F02
2: RS-485
3: RS-485
4: F02
5: RS-485
6: RS-485 (option)
7: RS-485 (option)
8: RS-485 (option)
H42 1
－
Y N
－
-
H43
－ －
Y N
－
H44 Startup T imes of Motor 1 Indication of cumulative startup times
－ －
Y N
－
H45 Mock Alarm 0:
1:
－ －
Y N 0 5-62
H47
－ －
Y N Set at
factory
shipping
H48
－ －
Y N
－
H49 Starting Mode (Delay time) 0.0 to 10.0 s 0.1
ｓ
Y Y 0.0 5-57
H50 0.1 Hz N Y 0.0 5-16
H51 (Voltage) 1 V N Y2 0
H52 0.1 Hz N Y 0.0
H53 (Voltage) 1 V N Y2 0
H54 0.01 s Y Y 6.00 -
H56 0.00 to 3600 0.01 s Y Y 6.00
H61 UP / DOWN Control 0: 0.00
－ －
N Y 1
(Initial frequency setting) 1: Last UP / DOWN command value on releasing run command
H63 Low Limiter (Mode selection) 0:
－ －
Y Y 0
1:
H64 (Lower limiting frequency) 0.1 Hz Y Y 1.6 -
-
5-26
5-55
Non-linear V/f Pattern 1
(Frequency)
Non-linear V/f Pattern 2
(Frequency)
0 to 240: Output an AVR-controlled voltage (for 200 V class series)
ACC/DEC T ime
(Jogging operation)
0 to 500: Output an AVR-controlled voltage (for 400 V class series)
0.00 to 3600
*ACC time and DEC time are common.
Data setting range
Indication for replacing capacitors on printed circuit boards (0000 to FFFF:
Hexadecimal). Resettable.
RS-485 (option)
Enable (With PT C, the inverter immediately trips with
0h4
displayed.)
F01/C30
Initialize all function code data to the factory defaults
Enable (At restart after momentary power failure and at normal start)
Indication of cumulative run time of cooling fan for replacement
999 : Automatically determined by inverter
Cumulative Run T ime of Capacitors on
Printed Circuit Boards
Acceleration/Deceleration Pattern
Rotational Direction Limitation
Initial Capacitance of DC Link Bus
Capacitor
Name
Deceleration T ime for Forced Stop
Frequency command
Restart Mode after Momentary Power
Failure
(Restart time)
T hermistor (Mode selection)
Capacitance of DC Link Bus Capacitor
If the output frequency lowers less than the one limited by F16
(Frequency limiter: Low), decelerate to stop the motor.
Indication for replacing DC link bus capacitor (0000 to FFFF: Hexadecimal)
Enable (At restart after momentary power failure)
F01/C30
Indication for replacing DC link bus capacitor (0000 to FFFF: Hexadecimal)
Cumulative Run T ime of Cooling Fan
Instantaneous Overcurrent
0.0 (Depends on F16 (Frequency limiter: Low))
0.1 to 60.0
RS-485
F01/C30
RS-485
RS-485 (option)
RS-485
RS-485 (option)
Limit by F16 (Frequency limiter: Low) and continue to run
0: Disable
1 to 10
0.01 to 100.00
999: Follow the current limit command
0.0 to 30.0
0.0 : Cancel
0.1 to 400.0
0.0 : Cancel
0.1 to 400.0
0 to 240 : Output an AVR-controlled voltage (for 200 V class series)
0 to 500 : Output an AVR-controlled voltage (for 400 V class series)
Disable
Enable (Once a mock alarm occurs, the data automatically returns to
0.)