FE FRENIC-Multi series, Instruction Manual

Page: 79 / 196

5-4
(E code continued)
Code
Incre-
ment
Unit
Change
when
running
Data
copying
Default
setting
Refer to
page:
E29 Frequency Arrival Delay T ime 0.01 to 10.00 0.01 s Y Y 0.10 5-47
E30 0.0 to 10.0 0.1 Hz Y Y 2.5
E31 0.0 to 400.0 0.1 Hz Y Y T able A *4 -
E32 (Hysteresis width) 0.0 to 400.0 0.1 Hz Y Y 1.0
E34 5-47
(Level) 0.01 A Y Y1
Y2
E35 (T imer) 0.01 to 600.00 *1 0.01 s Y Y 10.00
E37 0.01 A Y Y1
Y2
E38 (T imer) 0.01 to 600.00 *1 0.01 s Y Y 10.00
E39 0.000 to 9.999 0.001
－
Y Y 0.000 5-48
E40 PID Display Coefficient A -999 to 0.00 to 9990 *1 0.01
－
Y Y 100 -
E41 PID Display Coefficient B -999 to 0.00 to 9990 *1 0.01
－
Y Y 0.00
E42 LED Display Filter 0.0 to 5.0 0.1 s Y Y 0.5
E43 0: Speed monitor (select by E48)
－ －
Y Y 0
3: Output current
4: Output voltage
8: Calculated torque
9: Input power
10: PID command
12: PID feedback amount
13: T imer
14: PID output
15: Load factor
16: Motor output
21: Reserved *2
22: Reserved *2
E45 0:
－ －
Y Y 0
1:
E46 (Language selection) 0: Japanese
－ －
Y Y T able A *4
1: English
2: German
3: French
4: Spanish
5: Italian
E47 (Contrast control) 0 (Low) to 10 (High) 1
－
Y Y 5
E48 LED Monitor (Speed monitor item) 0: Output frequency (Before slip compensation)
－ －
Y Y 0
1: Output frequency (After slip compensation)
2: Reference frequency
3: Motor speed in r/min
4: Load shaft speed in r/min
5: Line speed in m/min
6: Constant feeding rate time
E50 0.01 to 200.00 *1 0.01
－
Y Y 30.00
E51 0.001
－
Y Y 0.010
E52 Keypad (Menu display mode) 0: Function code data editing mode (Menus #0 and #1)
－ －
Y Y 0 -
1: Function code data check mode (Menu #2)
2: Full-menu mode (Menus #0 through #6)
E59 0: Current input (C1 function), 4 to 20 mADC
－ －
N Y 0 5-48
1: Voltage input (V2 function), 0 to +10 VDC
E61
－ －
N Y 0 5-49
E62 0: None
－ －
N Y 0
(C1 function) 1: Auxiliary frequency command 1
E63 2: Auxiliary frequency command 2
－ －
N Y 0
(V2 function) 3: PID command 1
5: PID feedback amount
E65 1 % Y Y 999
Bar charts for output frequency, current and calculated torque
100% of the
motor rated
current
Selecting function code data assigns the corresponding function to
terminals [12] and [C1] (C1/V2 function) as listed below.
0.00 : Disable
Current value of 1 to 200% of the inverter rated current
Name
Terminal [C1] Signal Definition
(C1/V2 Function)
Coefficient for Speed Indication
Terminal [12] Extended Function
Frequency Arrival
(Hysteresis width)
Frequency Detection (FDT )
Overload Early Warning/Current
Detection
LCD Monitor *3 (Item selection)
Display Coefficient for Input Watt-hour
Data
Reference Loss Detection
(Continuous running frequency)
Current Detection 2 (Level)
Terminal [C1] Extended Function
Terminal [C1] Extended Function
(Detection level)
Coefficient for Constant Feeding Rate
Time
100% of the
motor rated
current
Running status, rotational direction and operation guide
0: Decelerate to stop
20 to 120
999: Disable
0.000 (Cancel/reset
）
0.001 to 9999
Data setting range
LED Monitor (Item selection)
0.00 : Disable
Current value of 1 to 200% of the inverter rated current
5-48
The shaded function codes ( ) are applicable to the quick setup.
*
1
When you make settings from the keypad, the incremental unit is restricted by the number of digits that the LED monitor can
display.
(Example) If the setting range is from -200.00 to 200.00, the incremental unit is:
"1" for -200 to -100, "0.1" for -99.9 to -10.0 and for 100.0 to 200.0, and "0.01" for -9.99 to -0.01 and for 0.00 to 99.99.
* 2
These function codes and their data are displayed, but they are reserved for particular manufacturers. Unless otherwise
specified, do not access these function codes.
*
3
These function codes are for use with an optional multi-function keypad.
* 4
Default settings for these function codes vary depending on the shipping destination. See Table A "Default Settings
Depending on the Shipping Destination" on page 5-11.