FE FRENIC-Multi series, Instruction Manual

Page: 76 / 196

5-1
Chapter 5 FUNCTION CODES
5.1 Function Code Tables
The following tables list the function codes available for the FRENIC-Multi series of inverters.
F codes: Fundamental Functions
Code
Incre-
ment
Unit
Change
when
running
Data
copying
Default
setting
Refer to
page:
F00 0:
－ －
Y Y 0
1:
2:
3:
F01 0: UP/DOWN keys on keypad
－ －
N Y 0
1: Voltage input to terminal [12] (-10 to +10 VDC)
2:
3:
5:
7: T erminal command UP / DOWN control
11: DIO interface card (option)
12: PG interface card (option)
F02 0:
－ －
N Y 2
1: T erminal command FWD or REV
2: RUN/ST OP keys on keypad (forward)
3: RUN/ST OP keys on keypad (reverse)
F03 25.0 to 400.0 0.1 Hz N Y T able A *4
F04 25.0 to 400.0 0.1 Hz N Y T able A *4 5-16
F05 0: 1 V N Y2 T able A *4
80 to 240:
160 to 500:
F06 80 to 240: 1 V N Y2 T able A *4
160 to 500:
F07 0.00 to 3600 0.01 s Y Y 6.00
F08 0.00 to 3600 0.01 s Y Y 6.00
F09 0.1 % Y Y Depending
on the
inverter
capacity
5-18
F10 1:
－ －
Y Y 1 5-20
2:
F11 0.01 A Y Y1
Y2
100% of the
motor rated
current
F12 0.5 to 75.0 0.1 min Y Y 5.0
F14 0: Disable restart (Trip immediately)
－ －
Y Y T able A *4 5-23
1: Disable restart (Trip after a recovery from power failure)
4:
5:
F15 Frequency Limiter (High) 0.0 to 400.0 0.1 Hz Y Y 70.0 5-26
F16 (Low) 0.0 to 400.0 0.1 Hz Y Y 0.0
F18 -100.00 to 100.00 *1 0.01 % Y* Y 0.00 5-27
0.0 to 60.0 0.1 Hz Y Y 0.0 5-28
F21 (Braking level) 0 to 100 1 % Y Y 0
F22 (Braking time) 0.01 s Y Y 0.00
F23 0.1 to 60.0 0.1 Hz Y Y 0.5 5-29
F24 (Holding time) 0.01 to 10.00 0.01 s Y Y 0.00
F25 0.1 to 60.0 0.1 Hz Y Y 0.2
F26 0.75 to 15 1 kHz Y Y T able A *4
F27 (Tone) 0: Level 0 (Inactive)
－ －
Y Y 0
1: Level 1
2: Level 2
3: Level 3
5-17
5-13
5-15
F20
(Braking starting frequency)
Motor Sound (Carrier frequency)
Restart Mode after Momentary Power
Failure
Deceleration Time 1
Rated Voltage at Base Frequency 1
Electronic T hermal Overload
Torque Boost 1
(Select motor characteristics)
(Overload detection level)
Data setting range
Protection for Motor 1 For an inverter-driven motor, non-ventilated motor, or motor with
Disable both data protection and digital reference protection
For a general-purpose motor with shaft-driven cooling fan
Name
Enable data protection and disable digital reference protection
Disable data protection and enable digital reference protection
Current input to terminal [C1] (C1 function) (4 to 20 mA DC)
Sum of voltage and current inputs to terminals [12] and [C1]
(C1 function)
Data Protection
Frequency Command 1
Operation Method
Maximum Frequency 1
Base Frequency 1
Maximum Output Voltage 1
Acceleration Time 1
(T hermal time constant)
Output an AVR-controlled voltage (for 400 V class series)
Output an AVR-controlled voltage (for 200 V class series)
Output an AVR-controlled voltage (for 400 V class series)
0.0 to 20.0
(percentage with respect to "F05: Rated Voltage at Base Frequency 1")
Note: This setting takes effect when F37 = 0, 1, 3, or 4.
Note: Entering 0.00 cancels the acceleration time, requiring external
soft-start.
Note: Entering 0.00 cancels the deceleration time, requiring external
soft-start.
0.00 : Disable
0.01 to 30.00
Voltage input to terminal [C1] (V2 function) (0 to 10 VDC)
RUN/ST OP keys on keypad (Motor rotational direction specified by
terminal command FWD / REV )
Output a voltage in proportion to input voltage
Output an AVR-controlled voltage (for 200 V class series)
Enable both data protection and digital reference protection
0.00: Disable
1 to 135% of the rated current (allowable continuous drive current) of the
motor
Starting Frequency 1
DC Braking 1
Stop Frequency
Bias (Frequency command 1)
(Mode selection)
separately powered cooling fan
Enable restart (Restart at the starting frequency, for low-inertia load)
Enable restart (Restart at the frequency at which the power failure
occurred, for general loads)
The shaded function codes ( ) are applicable to the quick setup.
* 1
When you make settings from the keypad, the incremental unit is restricted by the number of digits that the LED monitor can
display.
(Example) If the setting range is from -200.00 to 200.00, the incremental unit is:
"1" for -200 to -100, "0.1" for -99.9 to -10.0 and for 100.0 to 200.0, and "0.01" for -9.99 to -0.01 and for 0.00 to 99.99.
*
4
Default settings for these function codes vary depending on the shipping destination. See Table A "Default Settings
Depending on the Shipping Destination" on page 5-11.