Epygi Quadro4Li, Administrator'S Manual

Page: 95 / 145

Quadro4Li Manual II: Administrator's Guide Administrator’s Menus
Quadro4Li; (SW Version 5.3.x)
94
The Call Routing Wizard - Page 3 appears if the Fill Call
Source Information checkbox had been enabled on Page 1 of
the Call Routing Wizard. It will require information about the
inbound caller.
The Source Number Pattern field requires the caller address
for which the current route will be applied. The complete list of
characters and wildcards allowed in this text field is given
below .
The Source Type drop down list gives you the option to select
the call type (PBX, SIP, ISDN, Any) used by the inbound caller
to reach the Quadro.
Fig. II-163: Call Routing Wizard - page 3
The settings in the Caller ID Modification group allow Caller IDs of inbound calls to be modified.
•
The Number of Discarded Symbols (NDS) text field requires the number of digits that should be discarded from the beginning of the Inbound
Caller Pattern . The field should be empty if digits do not need to be discarded. Only numeric values are allowed for this field, otherwise the
error message “Error: Number of Discarded Symbols is incorrect - digits allowed only” will appear.
•
The Prefix text field requires entering the symbols (alphanumerics and any characters supported in the SIP username) that will be placed in
front of the Inbound Caller Pattern instead of the discarded digits. (For example, if the routing pattern is 12345, the Number of Discarded
Symbols is two, and the prefix digits are 909, the final phone number will be 909345.) Wildcards are allowed here.
•
The Discard Non-Numeric Symbols checkbox is used to discard any non-numeric symbols from the Inbound Caller Pattern .
•
The Display Name text field allows you to replace an original caller’s ID with the custom display name for the corresponding routing rule. This
field is optional and when it is left empty, an original caller ID will be displayed on the called destination’s phone, otherwise the name inserted
here will appear on the phone. This field is not available for PBX-Voicemail call type routing rules.
•
The Remove Display Name checkbox is used to remove caller IDs from calls made with this routing rule. This field is not available for PBX-
Voicemail call type routing rules.
The Next button will open the Call Routing Wizard - Page 4 where different information about Inbound Caller will be required depending on the
selected Inbound Call Type . For the SIP Inbound Call Type, the Inbound Host text field will require one or more IP addresses or host names of the
SIP server where the caller is registered, or the caller’s device if they are direct calls, separated by a space. In case of ISDN Inbound Call Types
selected, Inbound Port ID drop down list will require to select the Trunk number, and on the next step, a list of timeslot(s) used to receive calls from
the defined caller.
The
Call Routing Wizard – Date/Time Rules page appears if the
Set Date / Time Period(s) checkbox previously had been enabled
on Page 1 of the Call Routing Wizard . It will require information
about the pattern validity period(s).
This page provides selection between
Typical and Custom
date/time rule definitions.
The Typical selection contains the following group of radio buttons
that are used to select the frequency of the corresponding routing
pattern that is to take place:
•
Daily
•
Weekly – the preferred weekday(s) should be selected for
this option.
•
Monthly – the calendar day should be selected for this
option.
•
Annually – the calendar day and month should be selected
for this option.
In the Available Time Period drop down lists, the time range of
the pattern validation should be defined. Any time selected in this
field will be considered corresponding to the Quadro’s
Time/Date
Settings.
The Custom selection provides the option to manually define the
validity period(s). Use the following format to insert pattern
date/time rule(s):
[Month,Month-Month,...][Day-Day,Day,...][hh:mm-hh:mm,...]; ...
Fig. II-164: Call Routing Wizard –Date/Time Rules page