Epson SureColor F7170 User Manual Download Page 64

Page: 64 / 188

Basic Operations

9. Lower the roll onto the roll support.

Before Printing

To maintain print quality, perform the following inspection before starting work each day.

❏

Print a check pattern to check for clogged nozzles.

❏

Perform head cleaning if parts of the pattern are faint or missing.

See “Checking for Clogged Nozzles” on page 84.

See “Head Cleaning” on page 86.

Saving Optimal Settings for the Current Media (Print Media
Settings)

A variety of media settings can be optimized for the current media and stored in the printer.

Once frequently used settings have been stored in a media setting bank, they can be
recalled to instantly optimize multiple parameters.

The printer offers a total of 30 media setting banks.

This section describes how to create media setting banks and the settings that can be
stored.

Summary of Contents for SureColor F7170





























































































































































































Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands

Epson SureColor F7170, User Manual

Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands