Epson SureColor F7170 User Manual Download Page 66

Page: 66 / 188

Basic Operations

Saving Settings

Follow the steps below to save media settings.

Choosing a Media Setting Bank

1. After confirming that the printer is ready to print, press the

Menu

button.

The settings menu will be displayed.

2. Select

Media Setup

and press the

button.

3. Use the

buttons to select

Customize Settings

and press the

button.

4. Use the

buttons to select a media setting bank number between 1 and 30 and then

press the

button.

Note that any settings already saved to the printer will be overwritten.

Setting Name

Name the media setting bank. Using distinctive names makes it easier to select banks for
use.

1. Select

Setting Name

and press the

button.

2. Use the

buttons to display letters and symbols. When the desired character is

displayed, press the

button to select the next entry position.

Mistakes can be erased by pressing the

button to delete the previous character and

move the cursor back one spot.

Summary of Contents for SureColor F7170





























































































































































































Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands

Epson SureColor F7170, User Manual

Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands