Epson SureColor F7170 User Manual Download Page 107

Page: 107 / 188

Maintenance

107

2. Lift the lock lever for the slider of the chip unit you intend to replace.

3. Insert a finger into the groove on the top of the slider and pull straight outward.

Important:

When the remaining ink is 70 mm (2.8 inches) or more from the bottom of the ink tank and
a message appears stating,

Refill Ink Tank

, it is time to replace the ink tank. We

recommend replacing the ink tank at this time. Replacements and repairs will be provided
for a fee.

During replacements and repairs, the ink in the ink tank is discarded. This is necessary
because fine dirt, dust, and other foreign bodies in the ink cause the ink tank to
malfunction.

The ink tank replacement interval depends on the usage environment and conditions.

Important:

Do not tilt the slider. If the chip unit is dropped it may break.

Summary of Contents for SureColor F7170





























































































































































































Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands

Epson SureColor F7170, User Manual

Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands