Epson SureColor F7170 User Manual Download Page 162 | Manualshive

Page: 162 / 188

background image

Appendix

162

Chapter 6

Appendix

Options and Consumable Products

The following options and consumable products are available for use with your printer.

For the latest information, see the Epson website.

Important:

Refilling the ink tank with an ink pack not specified in this manual can damage the printer.
Epson is not responsible for any damages or injuries incurred through the use of non-Epson
ink packs, even if the printer is still within warranty.

Product

Part number

Explanation

Ink packs

Black

T741100

Epson recommends the use of genuine Epson ink packs. Epson cannot
guarantee the quality or reliability of non-genuine ink. The use of
non-genuine ink may cause damage that is not covered by Epson’s
warranties, and under certain circumstances, may cause erratic printer
behavior. Information about non-genuine chip unit status may not be
displayed,and use of non-genuine ink is recorded for possible use in
service support. See

“Chip Unit Replacement and Ink Refills” on

page 104.

Cyan

T741200

Magenta

T741300

Yellow

T741400

Maintenance kit

T724200

Contains the cleaning sticks, gloves, wiper, and wiper cleaner required
for printer maintenance. See

“Maintenance Around the Print Head” on

page 88.

Waste ink bottle

T724000

Identical to the waste ink bottle supplied with the printer.

Media holding plate

C12C890891

Identical to the media holding plates supplied with the printer.

«
...
160
161
162
163
164
...
»

Summary of Contents for SureColor F7170





























































































































































































Reviews:

No comments

Related manuals for SureColor F7170

Color imageCLASS MF8580Cdw

Brand: Canon Pages: 36

Color imageCLASS MF8580Cdw

Brand: Canon Pages: 20

Color imageCLASS MF8280Cw

Brand: Canon Pages: 24

Color imageCLASS MF8080Cw

Brand: Canon Pages: 39

Color imageCLASS MF8050Cn

Brand: Canon Pages: 32

Color imageCLASS LBP7660Cdn

Brand: Canon Pages: 2

Color imageCLASS 8180c

Brand: Canon Pages: 24

Brand: Canon Pages: 30

C3000 - MultiPASS Color Inkjet Printer

Brand: Canon Pages: 41

Color imageCLASS MF8170c

Brand: Canon Pages: 2

Color imageCLASS MF8170c

Brand: Canon Pages: 98

Color imageCLASS MF8170c

Brand: Canon Pages: 8

Color imageCLASS MF8080Cw

Brand: Canon Pages: 46

Color imageRUNNER LBP5360

Brand: Canon Pages: 3

Brand: Canon Pages: 4

Brand: Canon Pages: 18

MultiPASS MPC190

Brand: Canon Pages: 8

Brand: Ricoh Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands