Epson SureColor F7170 User Manual Download Page 97

Page: 97 / 188

Maintenance

Place it on the attachment point and press down until you hear a click.

5. Close both maintenance covers and press the

button.

The menus will close when the print head returns to its normal position.

Disposing of Waste Ink

When to Dispose of Waste Ink

Be sure to replace the waste ink bottle when the following message is displayed on the
control panel.

❏

Prepare empty waste ink bottle.

❏

Replace waste ink bottle and press

Leave the waste ink in the waste ink bottle for disposal; do not transfer it to another
container.

Be sure to read the Safety Data Sheet before a replacement procedure. You can download
it from your local Epson Web site.

Summary of Contents for SureColor F7170





























































































































































































Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands

Epson SureColor F7170, User Manual

Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands