Epson SureColor F7170 User Manual Download Page 50

Page: 50 / 188

Basic Operations

2. After confirming that the media is loaded correctly, press the

button to feed the media

as far as the auto take-up reel unit roll core holder.

3. Loosen the roll core holder locking screws and adjust the roll core holders so that the

gap between the two is wider than the media.

Center the roll supports between the roll holders.

Important:

Always press the

button to feed the media as far as the roll core holder. If the media is

pulled by hand, the media may twist during take-up.

Important:

If the left roll core handle shaft is not visible, rotate the handle until it stops. The media can
not be properly loaded if the handle shaft is not visible.

Summary of Contents for SureColor F7170





























































































































































































Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands

Epson SureColor F7170, User Manual

Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands