Epson SureColor F7170 User Manual Download Page 82

Page: 82 / 188

Maintenance

Chapter 3

Maintenance

Daily Maintenance

To maintain print quality, perform the following inspection and cleaning before starting work
each day.

Cleaning the Platen, Pressure Rollers, and Media Holding Plates

Ink and particles of paper and lint from the media accumulate on the platen, pressure
rollers, and media holding plates. Ink on these surfaces may be transferred to the media.
Clean them thoroughly.

1. Make sure the printer is turned off and the screen has turned off, and then unplug the

power cable from the outlet.

2. Wait one minute.

3. Open the front cover.

4. Raise the media loading lever.

5. Clean the pressure rollers.

Caution:

❏

The after heater may be hot; observe all necessary precautions. Failure to observe the
necessary precautions could result in burns.

❏

Be careful not to trap your hands or fingers when opening or closing the front cover.
Failure to observe this precaution could result in injury.

Important:

Continued use with lint, dust, or ink adhering to these surfaces could damage the print head or
clog the nozzles.

Summary of Contents for SureColor F7170





























































































































































































Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands

Epson SureColor F7170, User Manual

Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands