Epson SureColor F7170 User Manual Download Page 165

Page: 165 / 188

Appendix

165

Post-move setup

After moving the printer, follow the steps below to ready it for use.

1. Check that the new location is appropriate.

See the

Setup Guide.

2. If the media guide bar was removed, reattach it. See “Removing and Attaching the

Media Guide Bar” on page 165.

3. Plug in the power cables and turn the printer on.

See the

Setup Guide.

4. Perform a nozzle check to check for clogged nozzles. See

“Checking for Clogged

Nozzles” on page 84.

5. Perform Head Alignment and check print quality. See

“Head Alignment (manual)” on

page 67.

Removing and Attaching the Media Guide Bar

Use these parts to remove and reattach the media guide bar:

Removing the Media Guide Bar

1. Remove the media guide bar.

Use the included hexagon wrench (small) to completely loosen the 4 screws securing
the media guide bar, and then remove the media guide bar.

Important:

Use the casters on the dedicated printer stand to move the printer indoors a short distance
over a level floor. They cannot be used for transport.

Summary of Contents for SureColor F7170





























































































































































































Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands

Epson SureColor F7170, User Manual

Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands