Epson SureColor F7170 User Manual Download Page 26

Page: 26 / 188

Introduction

Notes on Handling Ink Packs and Ink Tanks

Note the following points when handling ink packs and ink tanks.

❏

Do not remove the ink tanks

Ink tanks are calibrated when installed. Removing them can harm quality and
functionality.

❏

Store ink packs at room temperature out of direct sunlight.

❏

To ensure print quality, use all the ink in the ink pack before one of the following
(whichever comes first):

❏

The date printed on the ink pack

❏

25 days from the day the ink tank was refilled from the ink pack

❏

If the ink pack has been stored in a cold location for a long period of time, keep at room
temperature for at least 4 hours before using.

❏

Be sure not to leave any ink in the ink pack when you refill an ink tank.

❏

Refill the ink tank as soon as possible after opening the ink pack.

❏

Do not place any objects on the ink tank or subject the tank to strong impacts.
Otherwise, the tank could be detached.

Handling Media

Note the following when handling or storing media. Media that is in poor condition will not
produce good quality prints.

Be sure to read the documentation provided with each type of media.

Notes on Handling

❏

Do not fold the media or damage the printable surface.

❏

Do not touch the printable surface. Moisture and oils from your hands can affect print
quality.

❏

When handling media, hold it by both edges. We recommend wearing cotton gloves.

❏

Keep the media dry.

Summary of Contents for SureColor F7170





























































































































































































Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands

Epson SureColor F7170, User Manual

Search results

Summary of Contents for SureColor F7170

Reviews:

Related manuals for SureColor F7170

Brands by name

Popular brands