Epson SureColor F7170 User Manual Download Page 105 | Manualshive

Page: 105 / 188

background image

Maintenance

105

Procedure for Chip Unit Replacement and Ink Refills

You can use the same procedure to replace chip units for all colors.

c

Caution:

❏

Store ink packs in a location out of reach of children.

❏

Wear protective eyewear and gloves when refilling ink.

Be sure to read the Material Safety Data Sheet (MSDS) before using ink packs. You
can download it at your local Epson Web site.

Should ink contact your skin or enter your eyes or mouth, immediately take the
following actions:

❏

If fluid adheres to your skin, immediately wash it off using large volumes of soapy
water. Consult a physician if the skin appears irritated or is discolored.

❏

If fluid enters your eyes, rinse immediately with water. Failure to observe this
precaution could result in bloodshot eyes or mild inflammation. If problems persist,
consult with a physician.

❏

If fluid enters your mouth, consult with a physician as soon as possible.

❏

If swallowed, do not induce vomiting. Consult with a physician as soon as possible.
If vomiting is induced, vomited material may enter the windpipe, which is
dangerous.

❏

Note the following points when refilling ink.

❏

Gently cut or tear off the ink pack spout opening.

If you cut the ink pack spout too quickly, ink may splatter.

❏

Do not squeeze open ink packs. Ink may spill.

❏

Gently tilt the ink pack when pouring ink into the ink tank.

«
...
103
104
105
106
107
...
»

Summary of Contents for SureColor F7170





























































































































































































Reviews:

No comments

Related manuals for SureColor F7170

Brand: Oki Pages: 4

Brand: Xerox Pages: 4

Brand: Xerox Pages: 2

Brand: Xerox Pages: 16

Brand: OKIDATA Pages: 182

Brand: Konica Minolta Pages: 40

Brand: Oce Pages: 306

Brand: Printek Pages: 31

Brand: Xerox Pages: 14

Brand: Oki Pages: 72

Brand: Edimax Pages: 93

Brand: Kyocera Pages: 13

Brand: Katun Pages: 2

Brand: Rokit Pages: 21

Monochrome Laser

Brand: Lexmark Pages: 1

Brand: Protech Systems Pages: 140

Brand: Oce Pages: 32

Brand: Xerox Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands