Epson SureColor F7170 User Manual Download Page 163 | Manualshive

Page: 163 / 188

background image

Appendix

163

Supported Media

Print quality is greatly affected by the type and quality of media used. Choose a media
suited to the task at hand. For information on use, refer to the documentation supplied with
the media or contact the manufacturer. We recommend that you print a test run and check
the results before purchasing media in large quantities.

Important:

Do not use media that is wrinkled, scuffed, torn, or dirty.

Roll core size

2 or 3 inch

Roll outer
diameter

Up to 250 mm (9.8 inches)

Media width

300 to 1626 mm (11.8 to 64 inches)

Media
thickness

Up to 1 mm (0.04 inch)

Roll weight

Up to 40 kg (88.2 lb)

«
...
161
162
163
164
165
...
»

Summary of Contents for SureColor F7170





























































































































































































Reviews:

No comments

Related manuals for SureColor F7170

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 97

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 151

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 120

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 97

SCX 4200 - B/W Laser - All-in-One

Brand: Samsung Pages: 95

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 172

ProXpress M337x

Brand: Samsung Pages: 56

PROXPRESS M332 SERIES

Brand: Samsung Pages: 50

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 8

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 134

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 112

Brand: Samsung Pages: 128

Brand: Samsung Pages: 152

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 207

ML 2150 - B/W Laser Printer

Brand: Samsung Pages: 237

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 103

ML 2150 - B/W Laser Printer

Brand: Samsung Pages: 217

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands