Endress+Hauser Nanomass Gas Density Operating Instructions Manual Download Page 3

Page: 3 / 92

Nanomass Gas Density

Hauser

Table of contents

Notes on the Operating Instructions. . . 5

1.1 Document function . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3 Technical documentation . . . . . . . . . . . . . . . . . . . . . 6

1.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 7

Basic safety instructions . . . . . . . . . . . . . 8

2.1 Requirements for personnel . . . . . . . . . . . . . . . . . . 8

2.2 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Occupational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.5 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.6 IT security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Product description . . . . . . . . . . . . . . . . 10

3.1 Product design . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Incoming acceptance and product
identification . . . . . . . . . . . . . . . . . . . . . 11

4.1 Incoming acceptance . . . . . . . . . . . . . . . . . . . . . . 11

4.2 Product identification . . . . . . . . . . . . . . . . . . . . . . 11

Storage, transportation, disposal of
packaging . . . . . . . . . . . . . . . . . . . . . . . . 14

5.1 Storage conditions . . . . . . . . . . . . . . . . . . . . . . . . 14

5.2 Transporting the product . . . . . . . . . . . . . . . . . . . 14

5.3 Disposal of packaging . . . . . . . . . . . . . . . . . . . . . . 14

Installation . . . . . . . . . . . . . . . . . . . . . . . 15

6.1 Installation conditions . . . . . . . . . . . . . . . . . . . . . 15

6.2 Mounting the measuring device . . . . . . . . . . . . . 18

6.3 Post-installation check . . . . . . . . . . . . . . . . . . . . . 19

Electrical connection . . . . . . . . . . . . . . . 20

7.1 Connection conditions . . . . . . . . . . . . . . . . . . . . . 20

7.2 Connecting the measuring device . . . . . . . . . . . . 22

7.3 Special connection instructions . . . . . . . . . . . . . . 24

7.4 Guaranteeing the degree of protection . . . . . . . 24

7.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . 25

Operating options . . . . . . . . . . . . . . . . . 26

8.1 Overview of operating options . . . . . . . . . . . . . . 26

8.2 Access to the measuring device via the local display

8.3 Access to the measuring device via the

"Nanomass Communication" operating tool . . . . 28

System integration. . . . . . . . . . . . . . . . . 34

9.1 Overview of device description files . . . . . . . . . . 34

9.2 Measured variables via serial interface . . . . . . . 34

10 Commissioning . . . . . . . . . . . . . . . . . . . 36

10.1 Installation and function check . . . . . . . . . . . . . . . 36

10.2 Switching on the measuring device . . . . . . . . . . . 36

10.3 Setting the operating language . . . . . . . . . . . . . . 36

10.4 Configuring the measuring device . . . . . . . . . . . . 36

10.5 Advanced settings . . . . . . . . . . . . . . . . . . . . . . . . . 41

10.6 Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

10.7 "Datalog Function" application package . . . . . . . . 43

10.8 "Concentration Measurement" application package

11 Operation . . . . . . . . . . . . . . . . . . . . . . . . 47

11.1 Changing the operating language . . . . . . . . . . . . 47

11.2 Configuring the local display . . . . . . . . . . . . . . . . . 47

11.3 Reading measured values on the local display . . 47

11.4 Accessing real-time measuring data . . . . . . . . . . 48

11.5 Retrieving measuring data . . . . . . . . . . . . . . . . . . 51

11.6 Adapting the measuring device to the process

conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

11.7 Updating the firmware . . . . . . . . . . . . . . . . . . . . . 53

12 Diagnostics and troubleshooting . . . . 54

12.1 General troubleshooting . . . . . . . . . . . . . . . . . . . . 54

12.2 Diagnostic information via light emitting diodes . .

12.3 Diagnostic information on local display . . . . . . . . 55

12.4 Diagnostic information in the operating tool . . . 56

12.5 Resetting the measuring device to factory default

settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

12.6 Performing density adjustment with air . . . . . . . 57

12.7 Device information . . . . . . . . . . . . . . . . . . . . . . . . . 57

13 Maintenance . . . . . . . . . . . . . . . . . . . . . 59

13.1 Maintenance tasks . . . . . . . . . . . . . . . . . . . . . . . . . 59

13.2 Measuring and test equipment . . . . . . . . . . . . . . . 59

13.3 Hauser services . . . . . . . . . . . . . . . . . . . . 60

14 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

14.1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

14.2 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

14.3 Hauser services . . . . . . . . . . . . . . . . . . . . 61

14.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

14.5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

15 Accessories. . . . . . . . . . . . . . . . . . . . . . . 63

15.1 Device-specific accessories . . . . . . . . . . . . . . . . . . 63

15.2 Service-specific accessories . . . . . . . . . . . . . . . . . 63

15.3 System components . . . . . . . . . . . . . . . . . . . . . . . . 64

16 Technical data . . . . . . . . . . . . . . . . . . . . 65

16.1 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

16.2 Function and system design . . . . . . . . . . . . . . . . . 65

Summary of Contents for Nanomass Gas Density





























































































Search results

Summary of Contents for Nanomass Gas Density

Reviews:

Related manuals for Nanomass Gas Density

Brands by name

Popular brands

Endress+Hauser Nanomass Gas Density, Operating Instructions Manual

Search results

Summary of Contents for Nanomass Gas Density

Reviews:

Related manuals for Nanomass Gas Density

Brands by name

Popular brands