Endress+Hauser Nanomass Gas Density Operating Instructions Manual Download Page 20

Page: 20 / 92

Electrical connection

Nanomass Gas Density

Hauser

Electrical connection

The measuring device does not have an internal circuit breaker. For this reason, assign

the measuring device a switch or power-circuit breaker so that the power supply line can

be easily disconnected from the mains.

7.1

Connection conditions

7.1.1

Required tools

• For cable entries: use an appropriate tool.

• When using stranded cables: use a crimper for wire end ferrule.

7.1.2

Connecting cable requirements

The connecting cables provided by the customer must fulfill the following requirements:

Electrical safety

In accordance with applicable national regulations.

Permitted temperature range

• –40 to 80 °C (–40 to 176 °F)

• Minimum requirement: cable temperature range

≥

ambient tempe 20 K

Power supply cable

Signal cable

USB cable

RS232 cable

Outer diameter

3.5 to 5 mm

Number of cores

Min. 2

Cable resistance

77.8

Ω

/km at 20 °C

Shielding

Single shielding

Shielding

A shielded cable is recommended. Observe grounding concept of the
plant.

Cable type

Mini USB, type B, Buccaneer; standard USB, type A

Cable length

Max. 5 m

Cable type

M12, 4-pin; D-Sub, 9-pin

Cable length

Max. 5 m

Transmission rate

57600 Bd

Summary of Contents for Nanomass Gas Density





























































































Search results

Summary of Contents for Nanomass Gas Density

Reviews:

Related manuals for Nanomass Gas Density

Brands by name

Popular brands

Endress+Hauser Nanomass Gas Density, Operating Instructions Manual

Search results

Summary of Contents for Nanomass Gas Density

Reviews:

Related manuals for Nanomass Gas Density

Brands by name

Popular brands