Endress+Hauser Nanomass Gas Density Operating Instructions Manual Download Page 23

Page: 23 / 92

Nanomass Gas Density

Electrical connection

Hauser

7.2.2

Connecting the signal cables

Signals can be transmitted digitally via a USB port or RS232 interface or by analog

communication via the passive 4-20 mA connection.

Connect the 4-20 mA cable

1. Strip 10 mm (0.4 in) of the cable and cable ends. In the case of stranded cables, also fit

ferrules.

2. Connect the cable to the 4-20 mA connector in accordance with the pin assignment

→



21.

3. Insert the connector into the 4-20 mA connection of the measuring device and screw

tight.

4. Connect the signal cable to the 12-24 V power supply

→



24.

Connect the RS232 cable (optional)

1. If necessary, strip 10 mm (0.4 in) of the cable and cable ends. In the case of stranded

cables, also fit ferrules.

2. Where applicable, connect the cable to the RS232 connector in accordance with the pin

assignment

→



21.

3. Connect the RS232 cable to the RS232 socket of the measuring device and the COM port

(RS232) of the PC and screw tight.

Connect the USB cable (optional)

1. Make sure that the measuring device is disconnected from the supply voltage.
2. Connect the USB cable to the USB port of the measuring device and the USB port of the

PC.

3. Secure the cable to the device with a protection cap and cable clamp.

Summary of Contents for Nanomass Gas Density





























































































Search results

Summary of Contents for Nanomass Gas Density

Reviews:

Related manuals for Nanomass Gas Density

Brands by name

Popular brands

Endress+Hauser Nanomass Gas Density, Operating Instructions Manual

Search results

Summary of Contents for Nanomass Gas Density

Reviews:

Related manuals for Nanomass Gas Density

Brands by name

Popular brands