Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 133

Page: 133 / 156

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Trouble-shooting

Hauser

133

110 (A110)

Alarm
B

Failure (F)

B>Checksum error in
EEPROM: configuration
segment

– The supply voltage is

disconnected when writing.

– Reestablish supply voltage.

Perform reset (Code 7864) if
necessary. Carry out calibration
again.

– Electromagnetic effects are

greater than specifications in the
technical data.



See Technical

Information TI00382P (Deltabar
S), TI00383P (Cerabar S) or
TI00416P (Deltapilot S).

– Block off electromagnetic effects

or eliminate sources of
disturbance.

– Main electronics defect.

– Replace main electronics.

113 (A113)

Alarm
B

Failure (F)

B>ROM failure in transmitter
electronic

– Main electronics defect.

– Replace main electronics.

115 (E115)

Error
B
factory
setting:
Warning C

Out of
specification
(S)

B>Sensor overpressure

– Overpressure present.

– Reduce pressure until message

disappears.

– Sensor defect.

– Replace sensor.

116 (W116)

Warning
C

Maintenance
request (M)

C>Download error, repeat
download

– The file is defect.

– Use another file.

– During the download, the data

are not correctly transmitted to
the processor, e.g. because of
open cable connections, spikes
(ripple) on the supply voltage or
electromagnetic effects.

– Check cable connection PC –

transmitter.

– Block off electromagnetic effects

or eliminate sources of
disturbance.

– Perform reset (Code 7864) and

carry out calibration again.

– Repeat download.

120 (E120)

Error
B
factory
setting:
Warning C

Out of
specification
(S)

B>Sensor low pressure

– Pressure too low.

– Increase pressure until message

disappears.

– Sensor defect.

– Replace sensor.

121 (A121)

Alarm
B

Failure (F)

B>Checksum error in factory
segment of EEPROM

– Main electronics defect.

– Replace main electronics.

122 (A122)

Alarm
B

Failure (F)

B>Sensor not connected

– Cable connection sensor –main

electronics disconnected.

– Check cable connection and

repair if necessary.

– Electromagnetic effects are

greater than specifications in the
technical data.



See Technical

Information TI00382P (Deltabar
S), TI00383P (Cerabar S) or
TI00416P (Deltapilot S).

– Block off electromagnetic effects

or eliminate source of
disturbance.

– Main electronics defect.

– Replace main electronics.

– Sensor defect.

– Replace sensor.

130 (A130)

Alarm
B

Failure (F)

B>EEPROM is defect.

– Main electronics defect.

– Replace main electronics.

131 (A131)

Alarm
B

Failure (F)

B>Checksum error in
EEPROM: min/max segment

– Main electronics defect.

– Replace main electronics.

132 (A132)

Alarm
B

Failure (F)

B>Checksum error in totalizer
EEPROM

– Main electronics defect.

– Replace main electronics.

133 (A133)

Alarm
B

Failure (F)

B>Checksum error in History
EEPROM

– An error occurred when writing.

– Perform reset (Code 7864) and

carry out calibration again.

– Main electronics defect.

– Replace electronics.

602 (W602)

Warning
C

Funktion
check (C)

C>Linearisation curve not
monotone

– The linearisation table is not

monotonic increasing or
decreasing.

– Add to linearisation table or

perform linearisation again.

Code

Error type/
NA 64

Corresponds
NE 107

Message/description

Cause

Measure

Prio
rity

Summary of Contents for Deltabar S PMD70





























































































































































Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands

Endress+Hauser Deltabar S PMD70, Operating Instructions Manual

Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands