Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 119

Page: 119 / 156

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

119

NUTS MATERIAL

For selecting and displaying the material of the nuts.

Prerequisite:

• Digital communication

DRAIN VENT MAT.

For selecting and displaying the material of the vent valves.

Prerequisite:

• Digital communication

DRAIN VENT POS.

For selecting and displaying the position of the vent valves.

Prerequisite:

• Digital communication

THREAD

For selecting and displaying the process connection thread.

Prerequisite:

• Digital communication

MOUNTING THREAD

For selecting and displaying the ways of securing the device.

Prerequisite:

• Digital communication

REMOTE SEAL +

For selecting and displaying the diaphragm seal type on the positive side.

Prerequisite:

• Digital communication

REMOTE SEAL –

For selecting and displaying the diaphragm seal type on the negative side.

Prerequisite:

• Digital communication

DIAPHRAG. MAT. +

For selecting and displaying the material of the process isolating diaphragm on the positive
side.

Prerequisite:

• Digital communication

DIAPHRAG. MAT. –

For selecting and displaying the material of the process isolating diaphragm on the
negative side.

Prerequisite:

• Digital communication

NR OF REMOTE SEAL

For selecting and displaying the number of diaphragm seals.

Prerequisite:

• Digital communication

FILL FLUID

For selecting and displaying the diaphragm seal fill fluid.

Prerequisite:

• Digital communication

Table 26: (GROUP SELECTION



) OPERATING MENU



TRANSMITTER INFO



SENSOR DATA

(all measuring modes)

Parameter name

Description

SENSOR SER. No. (250)
Display

Displays the serial number of the sensor (11 alphanumeric characters).

PRESS. SENS LOLIM (484)
Display

Displays the lower measuring limit of the sensor.

PRESS. SENS HILIM (485)
Display

Displays the upper measuring limit of the sensor.

MINIMUM SPAN (591)
Display

Displays the smallest possible span.

Table 25: (GROUP SELECTION



) OPERATING MENU



TRANSMITTER INFO



PROCESS

CONNECTION

Parameter name

Description

Summary of Contents for Deltabar S PMD70





























































































































































Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands

Endress+Hauser Deltabar S PMD70, Operating Instructions Manual

Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands