Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 97 | Manualshive

Page: 97 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

97

TEMP. ENG. UNIT (318)
Selection

Select the unit for the temperature measured values.



See also PCB TEMPERATURE (Page 117) and SENSOR TEMP. (Page 122).

Options:

• °C
• °F
• K
• R

Factory setting:

°C

DENSITY UNIT (001)/(812)
Options

Select density unit.

Options:

• g/cm

3

• kg/dm

3

• kg/m

3

• US lb/in

3

• US lb/ft

3

Factory setting:

kg/dm

3

ADJUST DENSITY
(007)/(316)
Entry

Enter density of fluid.

!

Note!

LIN. MEASURAND: "% (Level)", "Mass" and "Volume" and MEASUAND KOMB.:
If a change to dry calibration is made after a wet calibration using the CALIBRATION
MODE parameter (



Page 73 or 87), the density for this parameter must be entered

correctly before changing the calibration mode. In the event that the pressure falls with
increasing levels (LIN. MEASURED: Volume), such as in the case of a residual volume
measurement, a negative value shall be entered for this parameter.

Factory setting:

1.0

PROCESS DENSITY
(025)/(811)
Entry

Enter a new density value for density correction.
The calibration was carried out with the medium water, for example. Now the container
is to be used for another fluid with another density. The calibration is corrected
appropriately by entering the new density value in the PROCESS DENSITY parameter.

!

Note!

LIN. MEASURAND: "% (Level)", "Mass" and "Volume" and MEASUAND KOMB.:
If a change to dry calibration is made after a wet calibration using the CALIBRATION
MODE parameter (



Page 73 or 87), the density for this parameter must be entered

correctly before changing the calibration mode. In the event that the pressure falls with
increasing levels (LIN. MEASURED: Volume), such as in the case of a residual volume
measurement, a negative value shall be entered for this parameter.

Factory setting:

1.0

Table 16: (GROUP SELECTION



)



OPERATING MENU



SETTINGS



EXTENDED SETUP "Level"

Parameter name

Description

«
...
95
96
97
98
99
...
»

Summary of Contents for Deltabar S PMD70





























































































































































Reviews:

No comments

Related manuals for Deltabar S PMD70

Brand: Dakota Digital Pages: 38

Event Master E2

Brand: Barco Pages: 2

Brand: Barco Pages: 7

Brand: Barco Pages: 7

Brand: Tailfin Pages: 8

Brand: Omnicomm Pages: 20

Brand: omnicharge Pages: 12

Brand: NATURE & DECOUVERTES Pages: 13

Brand: Yealink Pages: 2

Legend G3 738 NGK

Brand: Valor Pages: 6

Brand: JANE Pages: 21

Brand: Camcar Pages: 2

Brand: Razorri Pages: 26

Brand: Nauticam Pages: 33

Brand: Tripp Lite Pages: 2

Brand: Victory 4x4 Pages: 13

BUNDLES S16 OPTICAL MOUSE WIRED

Brand: PORT DESIGNS Pages: 1

Brand: Datavideo Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands