Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 15 | Manualshive

Page: 15 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Level measurement

Hauser

15

5.2

"Level Easy Pressure" level selection

5.2.1

Calibration with reference pressure – wet calibration

Example:

In this example, the level in a tank should be measured in m. The maximum level is 3 m (9.8 ft).
The pressure range is set to 0 to 300 mbar (4.5 psi).

Prerequisite:

• The measured variable is in direct proportion to the pressure.
• The tank can be filled or emptied.

!

Note!
• See also Operating Instructions for Deltabar S (BA00270P) or Cerabar S (BA00271P), Section 6.5

"Level measurement" or Deltapilot S (BA00332P), Section 6.4 "Level measurement".

• The values entered for EMPTY CALIB./FULL CALIB. and SET LRV/SET URV must have a

minimum interval of 1% for the "Level Easy Pressure" level mode. The value will be rejected with
a warning message if the values are too close together. Further limit values are not checked; i.e.
the values entered must be appropriate for the sensor and the measuring task so that the
measuring device can measure correctly.

• For a description of the parameters mentioned, see

– Page 45, Table 2: MEASURING MODE
– Page 53, Table 6: POSITION ADJUSTMENT
– Page 58, Table 8: LEVEL SELECTION "Level Easy Pressure"

• For a description of further relevant parameters, see

– Page 96, Table 16: EXTENDED SETUP
– Page 122, Table 28: PROCESS VALUES.

#

Warning!
If the measuring mode is changed, the span setting (URV) must be verified in the "Calibration"



"Basic Setup" operating menu and, if necessary, reconfigured.

Description

1

Deltabar S: Before you configure the device for your
application, the pressure piping must be cleaned and
filled with medium. See Operating Instructions
BA00270P, Section 6.5.1

P01-PMP75xxx-19-xx-xx-xx-008

Fig. 3:

Calibration with reference pressure –
wet calibration

1

See Table, Step 9.

2

See Table, Step 10.

2

Carry out position adjustment if necessary. See Page 53,
Table 6: POSITION ADJUSTMENT.

3

If necessary, select the "Level" measuring mode via the
MEASURING MODE parameter.

On-site display:
Menu path: GROUP SELECTION



MEASURING

MODE

Digital communication:
Menu path: OPERATING MENU



SETTINGS



BASIC SETUP



MEASURING MODE

4

If necessary, select "Level Easy Pressure" level mode
using the LEVEL SELECTION parameter.

On-site display:
Menu path: GROUP SELECTION



MEASURING

MODE "Level"



LEVEL SELECTION

Digital communication:
Menu path: OPERATING MENU



SETTINGS



BASIC SETUP



MEASURING MODE "Level"



LEVEL SELECTION

➀

➁

0 mbar

300 mbar

3 m

0 m

«
...
13
14
15
16
17
...
»

Summary of Contents for Deltabar S PMD70





























































































































































Reviews:

No comments

Related manuals for Deltabar S PMD70

Brand: Vega Pages: 76

Brand: D-Link Pages: 36

Brand: Baltimore Aircoil Company Pages: 12

Brand: ULTIMATE SPEED Pages: 19

Brand: Galeo Pages: 19

Brand: GCE Pages: 16

Brand: GCC Technologies Pages: 12

Brand: Patton electronics Pages: 8

Brand: Harbor Freight Tools Pages: 4

Brand: Jabra Pages: 7

Brand: Jabra Pages: 2

Brand: Jabra Pages: 12

Brand: Magura Pages: 2

Brand: Zacuto Pages: 5

Brand: Vauxhall Pages: 2

Brand: X4-Life Pages: 2

Brand: Yakima Pages: 12

Brand: JEHNERT SOUND DESIGN Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands