Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 123

Page: 123 / 156

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

123

MEAS. VAL. TREND (378)
Display

Displays the trend of the pressure measured value.
Possibilities: increasing, decreasing, constant

LEVEL BEFORE LIN (050)
Display

Displays the level value prior to linearisation.

Prerequisite:

• LEVEL MODE = Linear or Height Linearized

Depending on the setting for the LIN. MEASURAND or COMB. MEASURAND
parameter, this parameter displays the current level in % or in a unit of level.

TANK CONTENT (370)
Display

Displays the level value after linearisation.

Prerequisite:

• LEVEL MODE = Pressure Linearized or Height Linearized

Depending on the settings for the LINd. MEASURAND or COMB. MEASURAND
parameter, the current tank content is displayed in % or in a unit of volume or mass. This
value corresponds to the MEASURED VALUE.

Table 29: (GROUP SELECTION



) OPERATING MENU



PROCESSINFO



PROCESS VALUES "Flow"

Parameter name

Description

Prerequisite

• MEASURING MODE = Flow (



Summary of Contents for Deltabar S PMD70





























































































































































Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands

Endress+Hauser Deltabar S PMD70, Operating Instructions Manual

Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands