Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 116

Page: 116 / 156

Description of parameters

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

116

Hauser

HART DATE (481)
Entry

Enter the date of the last configuration change.

Factory setting:

DD.MM.YY (date of final test)

PRIMARY VALUE IS
Display

This parameter displays the following measured value depending on the measuring mode
selected:
– Measuring mode "Pressure": PRESSURE
– "Level" measuring mode, "Linear" or "Pressure Linearized"

level type: LEVEL BEFORE LIN

– Measuring mode "Level", level type "Height Linearized": TANK CONTENT
– Measuring mode "Flow": SUPPRESSED FLOW



See also SECONDARY VAL. IS.

Prerequisite:

• Digital communication

THIRD VALUE IS

Select third process value.



See also SECONDARY VAL. IS.

Prerequisite:

• Digital communication

THIRD VALUE

Display third process value.



See also SECONDARY VAL. IS.

Prerequisite:

• Digital communication

4TH VALUE IS

Select fourth process value.



See also SECONDARY VAL. IS.

Prerequisite:

• Digital communication

4TH VALUE

Display fourth process value.



See also SECONDARY VAL. IS.

Prerequisite:

• Digital communication

Table 24: (GROUP SELECTION



) OPERATING MENU



TRANSMITTER INFO



TRANSMITTER DATA

Parameter name

Description

DEVICE SERIAL No (354)
Display

Displays the serial number of the device (11 alphanumeric characters).

ELECTR. SERIAL No (386)
Display

Displays the serial number of the main electronics (11 alphanumeric characters).

Table 23: (GROUP SELECTION



) OPERATING MENU



TRANSMITTER INFO



HART DATA

Parameter name

Description

Summary of Contents for Deltabar S PMD70





























































































































































Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands

Endress+Hauser Deltabar S PMD70, Operating Instructions Manual

Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands