Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 13

Page: 13 / 156

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Pressure measurement

Hauser

Note!
• See also Operating Instructions Deltabar S (BA00270P), Section 6.6 "Differential pressure

measurement", Cerabar S (BA00271P), Section 6.4 "Pressure measurement" or Deltapilot S
(BA00332P), Section 6.5 "Pressure measurement".

• Due to the orientation of the device, there may be a shift in the measured value, i.e. when the

container is empty or partly filled, the MEASURED VALUE parameter does not display zero.



To perform a position adjustment see also Page 53, Table 6: Position adjustment.

• For a description of the parameters mentioned, see

– Page 45, Table 2: MEASURING MODE
– Page 53, Table 6: POSITION ADJUSTMENT
– Page 55, Table 7: BASIC SETUP.

• For a description of further relevant parameters, see

– Page 96, Table 15: EXTENDED SETUP
– Page 121, Table 27: PROCESS VALUES.

Warning!
If the measuring mode is changed, the span setting (URV) must be verified in the "Calibration"



"Basic Setup" operating menu and, if necessary, reconfigured.

Note!
• You can also perform calibration without reference pressure by means of the QUICK SETUP

menu.



See Page 47 ff, Table 3: QUICK SETUP menu.

• You can also specify a customer-specific unit. See parameter description for PRESS. ENG. UNIT

(



Page 56).

Description

If necessary, select the "Pressure" measuring mode via
the MEASURING MODE parameter.

On-site display:
Menu path: GROUP SELECTION



MEASURING

MODE

Digital communication:
Menu path: OPERATING MENU



SETTINGS



BASIC SETUP



MEASURING MODE

P01-PMP71xxx-19-xx-xx-xx-000

P01-xxxxxxxx-05-xx-xx-xx-010

Fig. 2:

Calibration without reference pressure

See table, step 4.

See table, step 5.

On-site display:
Select BASIC SETUP function group.
Menu path: GROUP SELECTION



OPERATING



SETTINGS



BASIC SETUP

Select a pressure unit via the PRESS. ENG. UNIT
parameter, here mbar for example.

Select SET LRV parameter.

Enter value, here 0 mbar, for the SET LRV parameter

and confirm. This pressure value is assigned to the lower
current value (4 mA).

Select SET URV parameter.

Enter value, here 300 mbar (4.5 psi), for the SET URV
parameter and confirm. This pressure value is assigned to
the upper current value (20 mA).

Result:
The measuring range is set for 0...+300 mbar (4.5 psi).

[mA]

300

[mbar]

➀

➁

Summary of Contents for Deltabar S PMD70





























































































































































Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands

Endress+Hauser Deltabar S PMD70, Operating Instructions Manual

Search results

Summary of Contents for Deltabar S PMD70

Reviews:

Related manuals for Deltabar S PMD70

Brands by name

Popular brands