Endress+Hauser Deltabar S PMD70 Operating Instructions Manual Download Page 77 | Manualshive

Page: 77 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

77

100% POINT (813)
Entry

Enter level value for 100% point.

Prerequisite:

• LIN. MEASURAND = % (Level), CALIBRATION MODE = Dry

Example:

– The 100 %-point should correspond to 4 m (13 ft).
– Select the "m" unit via the HEIGHT UNIT parameter.
– Enter the value "4" for this parameter (100% POINT).

Factory setting:

1.0

ZERO POSITION (814)
Entry

Enter value for level offset.
If the measurement should not start at the mounting location of the device, e.g. for
containers with a sump, carry out zero point shift (level offset).

Prerequisite:

• CALIBRATION MODE = Dry

Factory setting:

0.0

P01-PMP75xxx-19-xx-xx-xx-001

Fig. 32:

Zero point shift

1

Device is mounted above the level lower range value: a positive value has to be
entered for ZERO POSITION.

2

Device is mounted below the level lower range value: a negative value has to be
entered for ZERO POSITION.

SET LRV (719)
Entry

Enter level value for the lower current value (4 mA).

Factory setting:

0.0

SET URV (720)
Entry

Enter level value for the upper current value (20 mA).

Factory setting:

100.0

DAMPING VALUE (247)
Entry

Enter damping time (time constant



).

The damping affects the speed at which all subsequent elements, such as the on-site
display, measured value and current output react to a change in the pressure.

Input range:

0.0...999.0 s

Factory setting:

2.0 s or as per order specifications

Table 11: (GROUP SELECTION



) OPERATING MENU



SETTINGS



BASIC SETUP "Level",

LEVEL MODE "Linear"

Parameter name

Description

➀

➁

«
...
75
76
77
78
79
...
»

Summary of Contents for Deltabar S PMD70





























































































































































Reviews:

No comments

Related manuals for Deltabar S PMD70

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 14

Brand: Panasonic Pages: 30

Brand: JANE Pages: 6

Brand: Hama Pages: 2

Brand: Feniex Pages: 6

Brand: Fencing SmartBox Pages: 11

Brand: Feiyu Pages: 4

Brand: FAZUA Pages: 84

Brand: GAI-Tronics Pages: 22

Brand: Hahnel Pages: 176

PORTABLE AIR CONDITIONER & COOLER

Brand: Icebreeze Pages: 12

Brand: Sanitas Pages: 52

Brand: X4-Life Pages: 2

WorkCentre Pro 123

Brand: Xerox Pages: 4

Brand: M-Audio Pages: 14

ORBISPHERE K1200

Brand: Hach Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands